mazda
mazda questions and answers
Sell or buy a mazda at the worlds only automotive search engine, Lemonfree.com cars
Q: What headlights could i use on my 1988 mazda b2200?
I am getting some Altezza carbon tail lights and I wanna know what headlights i could use that would look good with those or fit a mazda grille? I heard Ford Ranger lights work. Any ideas?
A: yup those ford ranger lights will work
Q: how does the cooling fan in a 1996 Mazda 121 actually work?
I have a 1996 Mazda 121, when I turned the engine on, the cooling fan does not move. Is it supposed to be like that? As far as I can see from the temp gauge, no overheating problem occurs, it's still on the normal range. Someone told me that the fans only work when the engine reaches a certain temperature, is this the case?
A: yes, is normal
that operation is cause by something call thermo-sensor, when it reach certain temp it starts the fan until the part is cool down then it shuts down the cuicuit until it needs to start again
Q: How many pulses per revolution does a 12A Mazda Rotary engine produce?
My friend and I are putting a tachometer by AutoMeter in our RX7, but we need to know how many pulses per revolution a 12A rotary engine makes. The engine is from a 1982 Mazda RX7.
Thanks.
The tach instructions say it can be set up for 2 ppr (4cyl), 3 ppr (6cyl), and 4 ppr (8cyl).
Would 3 pulses a revolution be the rotary's signal?
A: Each rotor will have 3 combustion events per rotor revolution (so 6 in total) ... but... each rotor revolution produces 3 crankshaft revolutions.
That would seem to indicate 2 ppr, but I would check on RX7Club.com to be sure.
Q: How do I change a brake light on a Mazda 323 1990 model?
My back rear brake light has gone out and I don't have the car manual. It's a Mazda 323 1990 model - can any one help out - even what kind of bulb I'm supposed to get?
A: Im not familiar with the model but inside of the vehicle you should be able to peel the cover off to gain access to the screws to remove it. then replace the bulb. and the material or plastic goes back the same way you removed it when you are finished.
Q: Why does a 2002 mazda millenia shifter lock up when in park?
my 2002 mazda millenia shifter locks up when in park and i have to use the overide to get the car out of park and to be able to drive it. what is the problem?
A: A couple of things can cause this. The brake pedal switch could fail and not send a signal to the lockout letting it know that the brake is on and it's ok to start. Another item could be the shiftlock cable under the shifter. If this has become detached or stretched, it will not engage the release to the shifter. One more item could be what is commonly called the neutral/safety switch - if this switch fails, it will not realize that the shifter is in park or neutral and, therefore, will not allow the shifter to release.
Hope this helps.
Q: Where can i find exterior window trim for my 93 mazda mx6?
The window trim on my mazda is faded and it makes my car look awful. Is it hard to install?
A: did you mean the vent visors? those things are stick with some kind to adhesive tape very simple to install
if not the vent visors you mean the metal thing that goes around the glass? you cant replace that because that is part of the door
take it to a shop and get it painted again
Q: What is the original coolant and power steering fluid color for Mazda year 1999 626 V6?
Does anyone know the original coolant and power steering fluid color for Mazda year 1999 626 V6?
Power Steering fuid is at the word min and it is slightly higher when it is warm. Should I need to add Power Steering fluid? Can I use Power Sterring fluid from Perstone?
Power Steering fluid is at the word "min" and it is slightly higher when it is warm. Should I add Power Steering fluid? Can I use Power Steering fluid from Perstone?
A: The power steering fluid for most mazda vehicles including your 626 is mercon 3 or mercon 5. Your coolant could be green or orange/pink. I know the 2000 models used orange for sure. Most of the time mazda used a color sticker near the radiator filler cap. It showed orange/pink, green or gold/yellow coolant in a bottle. If you are doing a complete flush you can put whatever you want back in it. But if you are topping it off definitely use whatever it has in it. You should not mix orange and green. Doing so will cause a chemical reaction that basically negates any boil-over/freeze protection.
Q: How do I disable the passenger side airbags on a 1989 Mazda pickup in order to make it safe for a childseat?
I need to put a child restraint seat in the front seat of my truck, but Mazda won't disable the airbags due to liability issues.
A: Pull the fuse, keep in mind this may also disable the drivers side as well (not sure if they each have their own fuse).
If you cant, or cant find it, if you explain why you want to disable it (baby seat) most mechanics would be happy to do it for you. The dealer may not, but others will be grateful you want to keep that baby safe and not take a chance.
Q: are the ford probe and the mazda the same type of vehicle?
I have a 1991 ford probe. The key for the ignition is a Mazda one. Are they interchangeable. Seems like the key is too small for the ignition switch.
A: The Ford Probe and the Mazda 6 are the same car beneath the sheet metal. Ford owns Mazda, or at lest did own Mazda when these cars were produced.
Q: Does anyone know how long the average Mazda vehicle runs?
I am searching for a new car. At the current moment I am comparing the Mazda 3 & 6, Honda Accord, Toyota Camry, and Hyundai Sonata. The Sonata has the better warranty but is also the least attractive. Any advice would help. Thanks!
A: stay away from hyundai, theyre pieces of crap. horrible resale valueee . the mazda 3&6 are good cars but cant compete with honda and toyota. honda and toyota have the best resale value and are the most reliable. id go for a new accord!
Q: Where is the engine coolant temperature sensor on a Mazda MX3?
I bought a performance chip that is suppose to connect to the engine coolant temperature sensor on a 95 Mazda Mx-3, 4 cylinder. But i dont know the location of the sensor
A: Follow your upper radiator hose back towards the engine. The hose connects to the thermostat housing. you should see 1 or more sensors/switches screwed into this housing or very close-by. The temp sensor will have only 1 wire. To make sure you have the right wire and sensor, let the engine warm up enough that the needle on your temp gauge has risen. Shut the engine off, (it is not recommended to plug in or unplug wires while the ignition is on) unplug the suspected wire and turn the ignition switch on. If the gauge no longer reads, you have your wire.
If you can't find the sensor near the thermostat housing, try looking on the end of the cylinder head opposite the timing belt.
Q: What is the cheapeast way to import a new Mazda Rx-8 ?
Hi I live in Brazil and want to import a new Mazda Rx-8 to the country. From where should I but it, America or Japan? From dealership or factory? Thanks in advance.
A: you should probably buy it in Miami since the closer you buy it to Brazil the cheaper it is to ship it. buy from a dealer you cannot buy from the factory.
Q: How much does it normally cost to replace a windshield and driver side window on a Mazda 4 door?
The car is a 1998 Mazda Protege 4 door and I was wondering if anyone knows the normal range for replacing those things.
A: i own a repair shop,and this usually cost around 300 dollars for everything ,,on one like this,,,some shops will be a few bucks higher,,and some a little lower,,if you look around ,,you can get a good deal on one,,good luck hope this help,s.
Q: Where can I find an good independent Mazda service centre in West London?
I am fed up of the main Mazda garage and rip off prices. Looking for an independent mechanic who is good with Mazda motor vehicles.
A: Use any independent garage - Mazda use Ford mechanical parts for the most, any garage should be familiar with them, so ask around & get a personal recommendation from friends or family. As you say, any main dealer will just rob you blind!
Q: How can someone safely increase the power of a 2008 Mazda RX-8?
I'm curious about how someone can increase the horsepower, and especially low-end torque, of the 2008 Mazda RX-8. I've head that turbochargers and superchargers tend to have ill effects on the engine (being a rotary), so I'm going to shy away from them. What kind of upgrades could be added to increase the power, what is an approximate cost, and how much would these parts increase performance?
A: You want torque, then the only way to get lots of torque out of a rotary is to do a 20B 3 rotor swap.
Rotary's are fine on boost, just dont over boost them. For some more torque a supercharger would be good as it gives full boost at all rpm's.
However cheap upgrades like air intake and exhaust will see you no more than a 2-4hp gain. Mazda did well with the stock ones and you cant really improve on them.
So for large performance gains, your going to need a deep pocket. If you wanted to go for a 20B, you wouldnt see change spare of $12,000 or more in america. But they do have lots and lots of torque and even more horsepower.